Code Reader 1200 Manual de instalación Pagina 35
- Pagina / 176
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
SOFTWARE CONFIGURATION STRINGS
23
3
Command Syntax
1. Enter Service (Serial String Programming) Mode
$S<CR>
This command automatically sets the reader communication parameters to
115200,N,8,1.
2. Send Command
Command
<CR> $
Parameter Value
Where:
Command:
Description
HAXX
Interface Selection
AA
Enable All Symbologies
AD
Disable All Symbologies
R
Reset Reader
CXXXXXX
Write Single Configuration Item to RAM
Parameter:
XXXX
A 4-character ASCII string
See Serial Configuration Strings Table
Value:
XX
A 2-character Hex string
See Serial Configuration Strings Table
3. Apply and Save Configuration to FLASH (permanent memory) and Exit Service Mode
$Ar<CR>
This command automatically returns the reader to the programmed
communication parameters.
- Reference Manual 1
- CONTENTS 3
- REFERENCES 9
- FCC COMPLIANCE 10
- POWER SUPPLY 10
- CE COMPLIANCE 10
- HANDLING 11
- 1 INTRODUCTION 13
- 1.3 AVAILABLE MODELS 14
- 1.4 ACCESSORIES 15
- 2 INSTALLATION 16
- INSTALLATION 17
- 2.1.4 Electrical Connections 20
- RS232 Interface 21
- Outputs 23
- 2.2 TC1200 CCD SCAN ENGINE 24
- 2.2.2 Electrical Connections 25
- USB Interface 26
- TC1200 EXTERNAL TRIGGER 27
- OUT1/2 28
- 2.3 POSITIONING 29
- 3.1 TC1200 CONFIGURATION 34
- RS232 Models 34
- USB Models 34
- Command Syntax 35
- 4 BARCODE CONFIGURATION 52
- ËÄ$P,HA00,PmÂÎ 52
- ËÄ$P,HA05,PmHÎ 52
- ËÄ$P,HA47,PmtÎ 53
- ËÄ$P,HA35,Pm]Î 53
- ËÄ$P,HA2B,PmWÎ 53
- ËÄ$P,HA2C,Pm_Î 53
- GLOBAL INTERFACE FEATURES 55
- AUD RATE 56
- ATA BITS 56
- TOP BITS 56
- BAUD RATE 57
- DATA BITS 58
- STOP BITS 58
- RS232/USB-COM 59
- INTERCHARACTER DELAY 60
- DISABLE CHARACTER 60
- ENABLE CHARACTER 60
- ACK/NAK OPTIONS 60
- ACK CHARACTER 60
- NAK CHARACTER 61
- ACK/NAK TIMEOUT 61
- ACK/NAK RETRY COUNT 61
- ACK/NAK ERROR HANDLING 61
- USB-KBD 62
- KEYBOARD COUNTRY 63
- KEYBOARD COUNTRY (CONTINUED) 64
- KEYBOARD INTERCODE DELAY 64
- SEND CONTROL CHARACTERS 65
- USB KEYBOARD SPEED 65
- KEYBOARD SPEED (CONTINUED) 66
- ËÄ$CKBSP09mRÎ 66
- ËÄ$CKBSP0Am3Î 66
- READING PARAMETERS 67
- ILLUMINATION MODE 68
- OPERATING MODE 68
- AUTOMATIC THRESHOLD 68
- PHASE OFF EVENT 69
- TIMEOUT 69
- SERIAL START 69
- SERIAL STOP 69
- LED INDICATION 69
- LABEL PROGRAMMING MODE 70
- EXPOSURE MODE 70
- READING CONDITIONS 70
- DATA FORMAT 71
- DATA TRANSMISSION 72
- CODE VERIFIER MODE 72
- MATCH STRING 72
- WRONG CODE STRING 72
- CASE CONVERSION 73
- GLOBAL PREFIX 73
- GLOBAL SUFFIX 73
- NO READ STRING 73
- TRANSMIT AIM IDS 74
- TRANSMIT CUSTOM LABEL IDS 74
- CUSTOM LABEL IDENTIFIERS 74
- Enter/Exit Configuration 75
- Enter/Exit Configuration 76
- DIGITAL OUTPUTS 78
- OUTPUT 1 ACTIVATION EVENT 79
- OUTPUT 1 DEACTIVATION EVENT 79
- OUTPUT 2 ACTIVATION EVENT 80
- OUTPUT 2 DEACTIVATION EVENT 80
- POWER SAVE 81
- SLEEP MODE TIMEOUT 82
- CODE SELECTION 83
- CHECK CHARACTER TX 85
- EXPAND TO EAN-13 85
- NUMBER SYSTEM TX 85
- UPC-A MINIMUM READS 86
- EXPAND TO UPC-A 87
- UPC-E MINIMUM READS 88
- ISBN CONVERSION 89
- ISSN CONVERSION 89
- FLAG 1 CHARACTER 90
- EAN-13 MINIMUM READS 90
- EAN-8 MINIMUM READS 91
- ENABLE OPTIONAL P2 ADD-ON 92
- ENABLE OPTIONAL P5 ADD-ON 92
- P2 MINIMUM READS 92
- P5 MINIMUM READS 93
- OPTIONAL ADD-ON TIMER 93
- GTIN FORMAT 94
- IN-STORE MINIMUM READS 95
- CODE 39 95
- CODE 39 FULL ASCII 95
- CODE 39 CHECK TX 96
- CODE 39 START/STOP TX 96
- CODE 32 CHECK TX 97
- CODE 32 START/STOP TX 97
- Code 39 Check Options 98
- Code 39 Decoding Options 98
- QUIET ZONES 100
- STITCHING 100
- SET LENGTH 101
- CODE 128 101
- GS1-128 ENABLE 101
- CODE LENGTH CONTROL 101
- EXPAND TO CODE 39 102
- Code 128 Check Options 102
- CHECK TX 102
- FUNCTION CHARACTER TX 102
- SUB-CODE CHANGE TX 102
- Code 128 Decoding Options 103
- MINIMUM READS 103
- DECODING LEVEL 103
- CHARACTER CORRELATION 104
- ISBT 128 CONCATENATION 105
- CONCATENATION MODE 105
- INTERLEAVED 2 OF 5 106
- CHECK CALCULATION 107
- ZERO PATTERN 109
- STANDARD 2 OF 5 110
- INDUSTRIAL 2 OF 5 113
- CODABAR 116
- CODABAR ABC 117
- Codabar Check Options 118
- START/STOP SET 118
- START/STOP TX 119
- START/STOP MATCH 119
- Codabar Decoding Options 119
- INTERDIGIT RATIO 120
- CODE 11 122
- Code 11 Check Options 123
- Code 11 Decoding Options 124
- GS1 DATABAR OMNIDIRECTIONAL 126
- GS1 DATABAR EXPANDED 127
- COUPON CONTROL 128
- GS1 DATABAR LIMITED 129
- CODE 93 130
- Code 93 Check Options 131
- Code 93 Decoding Options 132
- MSI Check Options 135
- MSI Decoding Options 136
- PLESSEY 137
- Plessey Check Options 138
- Plessey Decoding Options 138
- 5 PARAMETER REFERENCES 140
- Intercharacter Delay 141
- Disable Character 141
- Enable Character 142
- ACK NAK Options 142
- ACK Character 143
- NAK Character 143
- ACK NAK Timeout Value 144
- ACK NAK Retry Count 144
- Keyboard Intercode Delay 145
- 5.2 READING PARAMETERS 145
- 5.2.1 Illumination Mode 145
- Illumination Mode 145
- 5.2.2 Operating Mode 146
- Operating Mode 146
- Automatic Threshold 146
- Phase Off Event 147
- Timeout 147
- Serial Start 148
- Serial Stop 148
- 5.2.3 Good Read LED 149
- LED Indication 149
- 5.2.4 Exposure Mode 149
- 5.2.5 Preset Recipes 149
- Reading Conditions 149
- 5.3 DATA FORMATTING 150
- 5.3.1 Global Prefix/Suffix 151
- No Read String 152
- 5.3.2 Code Identifiers 153
- Label IDs 153
- Label ID: Pre-loaded Set 153
- TC1200 REFERENCE MANUAL 154
- Global AIM ID 155
- 5.3.3 Code Verifier 156
- Match String 156
- Wrong Code String 156
- 5.4 DIGITAL OUTPUTS 157
- Activation Event 157
- Deactivation Event 157
- Deactivation Timeout 157
- Active Level 157
- 5.5 POWER SAVE 158
- Sleep Mode Timeout 158
- 5.6 CODE SELECTION 158
- Decoding Level 158
- Interdigit Ratio 159
- Character Correlation 159
- Minimum Reads 159
- Stitching 160
- Quiet Zones 160
- 5.6.1 Concatenation 160
- Concatenation Mode 160
- 5.6.2 Set Length 161
- Set Length 1 161
- Set Length 2 162
- 6 MAINTENANCE 163
- 7 TECHNICAL FEATURES 164
- 7.1 READING DIAGRAMS 165
- A DEFAULT PARAMETERS TABLE 166
- Transmit Labels in 168
- GS1-128 Data Format) 168
- C ASCII/HEX/DECIMAL CHART 172
- ASCII CHART 173
- D RESERVED CHARACTERS 174
- DECLARATION OF CONFORMITY 175
Relacionado con productos y manuales para Lectores De Códigos De Barras Code Reader 1200
(54 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.049 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales